Case 1021G, 1021G X-DRIVE, 1121G, 1121G X-DRIVE Wheel Loader Pdf Operators Manual

Case 1021G, 1021G X-DRIVE, 1121G, 1121G X-DRIVE Wheel Loader Pdf Operators Manual 

This manual provides essential guidance for operators and maintenance personnel to ensure safe, efficient, and reliable machine performance.

• GENERAL INFORMATION
  • Note to the owner
  • Intended use
  • Electro-Magnetic Compatibility (EMC)
  • Metric and imperial units abbreviations
  • Operator’s manual storage on the machine
  • Machine orientation
  • Product identification
  • Identification of machine components
• SAFETY INFORMATION
  • Safety rules
  • Personal safety
  • Safety rules
  • Seat belts
  • Support strut and service link
  • Utility safety
  • Ecology and the environment
  • Hand signals
  • Safety signs
• CONTROLS AND INSTRUMENTS
  • Access to operator’s platform
    • Proper entry and exit
  • Operator’s seat
    • Overview
  • Forward controls
    • Front console
    • Steering column
    • Pedal controls
    • Joystick steering
  • Right-hand side controls
    • Overview
    • Multifunction keypad
    • Control lever operation
    • Parking brake
    • Arm pad
  • Exterior controls
    • Hood and Timed Disconnect Switches
  • Display
    • Display description
    • Status and warning icons
  • Climate controls
    • Climate controls
    • Cab air louvers
  • Windows
    • Windows
  • Internal cab lights
    • Cab lights
    • Courtesy Lights
• OPERATING INSTRUCTIONS
  • Commissioning the unit
    • Before starting the engine
  • Starting the unit
    • Starting the engine
    • Operating in extreme temperatures
    • Operating the machine
  • Stopping the unit
    • Stopping the machine
  • Moving the unit
    • Enabling the Auxiliary F-N-R switch
    • Ride Control
    • Control levers
    • Auxiliary Forward, Neutral, Reverse (F-N-R) switch
    • Transmission automatic mode
    • Throttle set (4-speed transmission only)
    • Loader functions
    • Parallel Lift
• TRANSPORT OPERATIONS
  • Road transport
    • Safety rules
  • Recovery transport
    • Transporting the machine
    • Traveling on public roads
    • Moving a disabled machine
• WORKING OPERATIONS
  • Preparing for work
    • Operating tips
    • Joystick steering operation
    • Payload
    • Auto Dig, Auto Dump and Auto Metering features
• MAINTENANCE
  • General information
    • Servicing
    • Remote Service Tool (RST)
    • Releasing pressure in the hydraulic system
    • General specification – Diesel fuel – Diesel fuel
    • General specification – Paraffinic (Diesel) Fuels
    • General specification
    • Fluids and lubricants
    • Engine cooling system
    • Automatic lubrication system (if equipped)
    • Selective Catalytic Reduction on Filter (SCRoF) – Overview
    • Selective Catalytic Reduction on Filter (SCRoF) system
  • Maintenance planning
    • Maintenance chart
  • Daily inspection
    • Daily inspection
  • Every 10 hours
    • Engine oil level – Check
  • Every 50 hours
    • Bucket/attachment fittings – Grease
    • Machine fittings – Grease
    • Hydraulic oil level – Check
    • Transmission oil level – Check
    • Engine coolant level – Check
  • Initial 100 hours
    • Wheel nuts tightening – Check
    • Axle cooler filters (if equipped) – Replace
    • Selective Catalytic Reduction (SCR) in-line filter (Initial) – Remove and Discard
    • Hydraulic oil filter (Initial) – Replace
    • Front and rear axle oil (Initial) – Change
    • Engine oil (Initial) – Change
    • Engine oil filter (Initial) – Replace
    • Fuel pre-filter (Initial) – Replace
    • Fuel filter (Initial) – Replace
  • Every 100 hours
    • Machine fittings – Grease
  • Initial 250 hours
    • Transmission Clutch (Initial) – Calibrate
  • Every 250 hours
    • Drive shaft slip joints – Grease
    • Cab air recirculation filter – Cleaning
    • Cab air pre-filter – Cleaning
    • Cab air filter – Cleaning
    • Wheels – Tire inflating
    • Drive belt – Check
    • Parking brake – Check
    • Auxiliary steering – Check
  • Every 500 hours
    • Engine oil – Change
    • Engine oil filter – Replace
    • Fuel pre-filter – Replace
    • Fuel filter – Replace
    • Fuel tank sediment – Drain
    • Front and rear axle oil level – Check
    • Roll Over Protective Structure (ROPS) – Check
    • Battery fluid level – Check
    • DEF/AdBlue® tank vent filter – Replace
  • Every 1000 hours
    • Pivot points – Grease
    • Water from hydraulic system – Drain
    • Drive belt – Replace
    • Cab air recirculation filter – Replace
    • Cab air pre-filter – Replace
    • Cab air filter – Replace
    • Engine breather filter – Replace
    • Front and rear axle oil – Change
    • Axle cooler filters (if equipped) – Replace
    • Alternator – Check
    • Starter motor – Check
  • Every 2000 hours
    • Transmission oil – Change
    • Transmission oil filter – Replace
    • Transmission breather – Cleaning
    • Transmission Clutch – Calibrate
    • Hydraulic oil filter – Replace
    • Primary engine air filter – Replace
    • Secondary engine air filter – Replace
    • Frame and cab – Lubricate
    • Engine valve clearance – Check and adjust
  • Every 3000 hours
    • Cold weather hydraulic oil – Change
  • Every 4000 hours
    • CVT Hydrostat filter – Replace
    • Supply module filter – Replace
    • Diesel Exhaust Fluid (DEF)/AdBlue® tank suction filter – Cleaning
    • Standard weather hydraulic oil – Change
    • Engine coolant – Change
  • As required
    • Fuel pre-filter – Drain fluid
    • DEF/AdBlue® tank neck filter – Cleaning
    • Urea Quality Sensor (UQS) – Replace
    • Diesel Exhaust Fluid (DEF)/AdBlue® tank suction filter – Replace
    • Manual Catalyst Management (MCM) – Regenerate
    • Air conditioning condenser – Cleaning
    • Cab service – Check
    • Windshield washer fluid level – Check
    • Cooling box components- Check and clean
    • DEF/AdBlue® tank – Drain
    • DEF/AdBlue® tank – Refill
  • ELECTRICAL SYSTEM
    • Battery – Cleaning
    • Battery electrolyte level – Check
    • Auxiliary battery connections – Check
    • Battery – Replace
    • Fuses and relays – Replace
    • Lights – Replace
  • Storage
    • Preparation
    • Every 30 days
    • Every 4 months
    • Removal
• SPECIFICATIONS
  • General specification
  • Machine specifications and dimensions
  • Torque charts
  • Material weights
• ACCESSORIES
  • General accessories
  • Telematics

Fast Download Speeds
Online & Offline Access
Access PDF Contents & Bookmarks
Full Search Facility
Print one or all pages of your manual